Octofloat Section Lengths

The Edgar Sealey & Sons Ltd Rods forum.
Jeremy Croxall
Zander
Posts: 3739
Joined: Tue Oct 27, 2015 8:05 am
8
Location: Matlock Derbyshire

Octofloat Section Lengths

Post by Jeremy Croxall »

Yesterday was cold, wet, grey, miserable and so was I.
I wanted to go fishing but just could not muster the get up and go to.... well, get up and go!
So instead I decided to knock up a rod rack from some bits of Oak which I obtained form my daughters cot. I hasten to add that she was not in it at the time having progressed to a bed several years ago. My wife couldn't bear to part with it so it has been stored in my workshop and has been cannibalised several times to provide oak for various projects (with permission of course).
Having completed it I was placing the rods on the rack and noticed that the tip section of my Octofloat was slightly shorter than the butt and middle section by about two inches. Is this normal or do you think it has lost a bit off the top? The rod has been restored and looks lovely in the rack along with my other cane rods.
I have tried to find a specification for the rod on the forum and an internet search did not provide any relevant info either.
Look forward to receiving your comments with fingers crossed.
Jeremy.
"Oh for want of rod and line I'd fish this stream serene, sublime".

Paul D

Re: Octofloat Section Lengths

Post by Paul D »

Sounds like it's lost a bit Jeremy, love to see your new rack. :Thumb:

Jeremy Croxall
Zander
Posts: 3739
Joined: Tue Oct 27, 2015 8:05 am
8
Location: Matlock Derbyshire

Re: Octofloat Section Lengths

Post by Jeremy Croxall »

Paul D wrote: Sun Jan 29, 2017 9:29 am Sounds like it's lost a bit Jeremy, love to see your new rack. :Thumb:
I'll send you a pic when I have cleaned it up and varished it, it's a bit basic mind.
Do you think the loss of two inches off the top will affect it's action much Paul?
"Oh for want of rod and line I'd fish this stream serene, sublime".

Paul D

Re: Octofloat Section Lengths

Post by Paul D »

Jeremy Croxall wrote: Sun Jan 29, 2017 9:47 am
Paul D wrote: Sun Jan 29, 2017 9:29 am Sounds like it's lost a bit Jeremy, love to see your new rack. :Thumb:
I'll send you a pic when I have cleaned it up and varished it, it's a bit basic mind.
Do you think the loss of two inches off the top will affect it's action much Paul?
The action will have changed ( stiffer) but unless you had a full length version to compare it too how would you ever know? Unless it's particularly precious too you I wouldn't worry about it Jeremy. :Hat:

Jeremy Croxall
Zander
Posts: 3739
Joined: Tue Oct 27, 2015 8:05 am
8
Location: Matlock Derbyshire

Re: Octofloat Section Lengths

Post by Jeremy Croxall »

Paul D wrote: Sun Jan 29, 2017 9:29 am Sounds like it's lost a bit Jeremy, love to see your new rack. :Thumb:
Here it is Paul:
Image Image

I notice the pics need rotating, any one know how to do it?
Last edited by Jeremy Croxall on Sun Jan 29, 2017 2:16 pm, edited 1 time in total.
"Oh for want of rod and line I'd fish this stream serene, sublime".

User avatar
Ljm183
Rainbow Trout
Posts: 3186
Joined: Fri Nov 25, 2011 12:34 pm
12
Location: Aveley, Essex

Re: Octofloat Section Lengths

Post by Ljm183 »

Measure the rod when put together, if it,s 11ft or more it,s OK . I had three Octofloats all had slightly shorter tip sections

Image

Jeremy Croxall
Zander
Posts: 3739
Joined: Tue Oct 27, 2015 8:05 am
8
Location: Matlock Derbyshire

Re: Octofloat Section Lengths

Post by Jeremy Croxall »

Ljm183 wrote: Sun Jan 29, 2017 1:45 pm Measure the rod when put together, if it,s 11ft or more it,s OK . I had three Octofloats all had slightly shorter tip sections

Image
Just measured it at 10' 10 3/4" :Cry:
"Oh for want of rod and line I'd fish this stream serene, sublime".

User avatar
Ljm183
Rainbow Trout
Posts: 3186
Joined: Fri Nov 25, 2011 12:34 pm
12
Location: Aveley, Essex

Re: Octofloat Section Lengths

Post by Ljm183 »

Jeremy Croxall wrote: Sun Jan 29, 2017 2:20 pm
Just measured it at 10' 10 3/4" :Cry:
Yep looks like you've lost a bit

Paul D

Re: Octofloat Section Lengths

Post by Paul D »

Jeremy Croxall wrote: Sun Jan 29, 2017 1:19 pm
Paul D wrote: Sun Jan 29, 2017 9:29 am Sounds like it's lost a bit Jeremy, love to see your new rack. :Thumb:
Here it is Paul:
Image Image

I notice the pics need rotating, any one know how to do it?
That's marvellous Jeremy, I love things made from "things" , very clever :Hat:

User avatar
Ljm183
Rainbow Trout
Posts: 3186
Joined: Fri Nov 25, 2011 12:34 pm
12
Location: Aveley, Essex

Re: Octofloat Section Lengths

Post by Ljm183 »

Jeremy Croxall wrote: Sun Jan 29, 2017 1:19 pm
I notice the pics need rotating, any one know how to do it?

If you're using a laptop or pc , right click on the picture and select view image the picture opens and it,s the right way.

It also gives you the option to zoom in.

--------------------------------------------------------------------------

I think the original being side on is something to do with Tinypic..

Post Reply

Return to “Edgar Sealey & Sons Ltd Cane Rods”