Hi folks
Can anyone advise on how one changes a Trudex from being a right hand wind to a left hand wind.
Many thanks in advance
Buller
Changing a Trudex from RHW to LHW
Re: Changing a Trudex from RHW to LHW
Nobby posted a tutorial a while back, it just involves reprofilling the pawl, works a treat.
- Mushy
- Arctic Char
- Posts: 1633
- Joined: Sat Mar 02, 2013 8:56 pm
- 11
- Location: Surrey
Re: Changing a Trudex from RHW to LHW
I think you can reverse the pawl but the whole lot needs unscrewing and with old soft muddied in screws that could be tricky unless you have spares ready!
Best Fishes
Mushy
Mushy
Re: Changing a Trudex from RHW to LHW
No unscrewing required Sir, simply lever the spring off the pawl and pop it out, nobbys mod involves reprofiling the pawl to give a soft "click" on the retrieve but a hard one when a fish takes line, well worth doing but you must follow the profile nobby shows, anyone kind enough to post the link? I'm a computer numpty
- Keston
- Tench
- Posts: 2587
- Joined: Sun Feb 08, 2015 5:48 pm
- 9
- Location: Fareham on the sunny south coast .
Re: Changing a Trudex from RHW to LHW
Very nearly John, somewhere he posted a diagram of the profile.
- SeanM
- Tench
- Posts: 2643
- Joined: Wed Sep 14, 2011 9:28 pm
- 12
- Location: Bradford, West Yorkshire
Re: Changing a Trudex from RHW to LHW
Quot homines, tot sententiae.
- Keston
- Tench
- Posts: 2587
- Joined: Sun Feb 08, 2015 5:48 pm
- 9
- Location: Fareham on the sunny south coast .
Re: Changing a Trudex from RHW to LHW
This the jobbie (take 2 ) ?
www.traditionalfisherman.com/viewtopic. ... wl#p332341
www.traditionalfisherman.com/viewtopic. ... wl#p332341
- Nobby
- Wild Carp
- Posts: 10983
- Joined: Sun Oct 02, 2011 2:40 pm
- 12
- Location: S.W.Surrey
- Contact:
Re: Changing a Trudex from RHW to LHW
viewtopic.php?f=279&t=20035&p=272563&hi ... ng#p272563
I'm glad this was brought up again as I've recently used the basic principle to convert another reel to LHW in the same way, but I made a discovery that is quite important.
If you don't 'wash out' the new profile towards the centre of the back edge of the pawl it tends not to centralise itself and doesn't return as you switch the check off again.
This wasn't so much of an issue with JW Youngs reels, but was more important with this last reel, a Grice and Young model.
With the Youngs reels the conversion does reduce spring pressure and it is often necessary to increase it again with a spring pre-loader. You can see I made one in metal but you can whittle one from a bit of float making BBQ skewer in seconds! Just carve flats on a 25mm piece, opposite one another and cut a notch in one flat to locate against the screw that holds the spring tight against the pawl...the one with the big flat head thus:
The shape I drew for the JW Youngs pawl is about right, but they DO vary! Other reels might need working on a bit more so go slowly you can always grind a bit more off, but you can't put it back.
I do tend to remove the screws and spring so as not to scratch the paintwork....like anything else the first time is hard...the tenth is easy.
I'm glad this was brought up again as I've recently used the basic principle to convert another reel to LHW in the same way, but I made a discovery that is quite important.
If you don't 'wash out' the new profile towards the centre of the back edge of the pawl it tends not to centralise itself and doesn't return as you switch the check off again.
This wasn't so much of an issue with JW Youngs reels, but was more important with this last reel, a Grice and Young model.
With the Youngs reels the conversion does reduce spring pressure and it is often necessary to increase it again with a spring pre-loader. You can see I made one in metal but you can whittle one from a bit of float making BBQ skewer in seconds! Just carve flats on a 25mm piece, opposite one another and cut a notch in one flat to locate against the screw that holds the spring tight against the pawl...the one with the big flat head thus:
The shape I drew for the JW Youngs pawl is about right, but they DO vary! Other reels might need working on a bit more so go slowly you can always grind a bit more off, but you can't put it back.
I do tend to remove the screws and spring so as not to scratch the paintwork....like anything else the first time is hard...the tenth is easy.