Restore a possible Reuben Heaton Rim Brake Ebonite Centrepin Reel

A forum to show any of your restored or built traditional fishing reels.
User avatar
Evert van der Plas
Perch
Posts: 427
Joined: Mon Dec 15, 2014 11:57 pm
9
Location: The Netherlands
Contact:

Restore a possible Reuben Heaton Rim Brake Ebonite Centrepin Reel

Post by Evert van der Plas »

i bought this reel to restore it to a nice working reel, it has a few difficult problems i have to solve. the pin holder and latch are tighten with iron screws and half rotten by rust. Rust expands so it was not possible to get them out the normal way but have to drill them out to release the pin holder and latch in the first time to clean them but also to make repairs on the Ebonite plate and rings. there also iron screws in the distance pillars and also half gone by rust. I have to make a decision to drill these screws out as well or leave them and try to fix the Ebonite on a different way
Image
Image
Image
Image
Image
Image

Image
Image
Image
When the reel is finished i post more pictures from the hole process

User avatar
JW1
Grayling
Posts: 732
Joined: Mon Dec 19, 2016 11:05 pm
7
Location: London

Re: Restore a possible Reuben Heaton Rim Brake Ebonite Centrepin Reel

Post by JW1 »

Have you tried heating the screws with the tip of a soldering iron, it may help to loosen them.

JW

Jeremy Croxall
Zander
Posts: 3741
Joined: Tue Oct 27, 2015 8:05 am
8
Location: Matlock Derbyshire

Re: Restore a possible Reuben Heaton Rim Brake Ebonite Centrepin Reel

Post by Jeremy Croxall »

Try soaking the screws with WD 40 every couple of hours or so through the course of a day before heating with a soldering iron as JW suggests above.
I would also try Jenolite rust remover.
If you can scrape out the slot to get a screw driver to fit, tapping the screw driver as you turn it sometimes helps.
Failing that you can buy a screw extractor, these are inexpensive and work reasonably well.
Good luck!
"Oh for want of rod and line I'd fish this stream serene, sublime".

User avatar
Evert van der Plas
Perch
Posts: 427
Joined: Mon Dec 15, 2014 11:57 pm
9
Location: The Netherlands
Contact:

Re: Restore a possible Reuben Heaton Rim Brake Ebonite Centrepin Reel

Post by Evert van der Plas »

JW1 wrote: Sun Jan 07, 2018 9:11 am Have you tried heating the screws with the tip of a soldering iron, it may help to loosen them.

JW
The reel is made from Ebonite so heating it up is no option i think, i drilled a few out and i think i leave the other screws in there and try to do the repairs a other way, Thanks JW

User avatar
Evert van der Plas
Perch
Posts: 427
Joined: Mon Dec 15, 2014 11:57 pm
9
Location: The Netherlands
Contact:

Re: Restore a possible Reuben Heaton Rim Brake Ebonite Centrepin Reel

Post by Evert van der Plas »

Jeremy Croxall wrote: Sun Jan 07, 2018 9:43 am Try soaking the screws with WD 40 every couple of hours or so through the course of a day before heating with a soldering iron as JW suggests above.
I would also try Jenolite rust remover.
If you can scrape out the slot to get a screw driver to fit, tapping the screw driver as you turn it sometimes helps.
Failing that you can buy a screw extractor, these are inexpensive and work reasonably well.
Good luck!
I try to scrape the slot out as well and tapping it out, how ever there is not much left from the slot and makes it very difficult. the screws are very small as well that makes it more difficult to drill a hole in it to use a screw extractor, the screw head could brake off as well
The screw head are only 3 - 4 mm wide. the reel is also made from Ebonite and makes it difficult to get them out without damage to the Ebonite
Thanks for your comments i rely appreciate it

User avatar
Evert van der Plas
Perch
Posts: 427
Joined: Mon Dec 15, 2014 11:57 pm
9
Location: The Netherlands
Contact:

Re: Restore a possible Reuben Heaton Rim Brake Ebonite Centrepin Reel

Post by Evert van der Plas »

The reel starts to look good and when i cleaned the rim brake a Patent number shows up under the layer dirt, No 7019. on a other post here on TFF the number corresponds with the year 1888. Wow that is a long time ago.
The metal bands are not nickel plated but silver plated that make it a very interesting reel

Image
Image

User avatar
Aitch
Pike
Posts: 6193
Joined: Sat Mar 23, 2013 11:03 am
11
Location: The Shades, Essex

Re: Restore a possible Reuben Heaton Rim Brake Ebonite Centrepin Reel

Post by Aitch »

Wow... that is exquisite....!
Just one more cast love, and I'll be on me way home

Leave nothing but footprints, take nothing but pictures and memories

User avatar
LuckyLuca
Barbel
Posts: 4792
Joined: Mon Jul 02, 2012 10:20 am
11
Location: Oxfordshire

Re: Restore a possible Reuben Heaton Rim Brake Ebonite Centrepin Reel

Post by LuckyLuca »

Amazing job as always Evert!
Another saved and beautiful again.
I walked across an empty land
I knew the pathway like the back of my hand
I felt the earth beneath my feet
Sat by the river and it made me complete.

User avatar
Wallys-Cast
Pike
Posts: 6579
Joined: Tue Mar 20, 2012 11:02 am
12
Location: Durham.

Re: Restore a possible Reuben Heaton Rim Brake Ebonite Centrepin Reel

Post by Wallys-Cast »

Another old warrior lives to fight another day. Well done Evert, great work..

Wal.

User avatar
Evert van der Plas
Perch
Posts: 427
Joined: Mon Dec 15, 2014 11:57 pm
9
Location: The Netherlands
Contact:

Re: Restore a possible Reuben Heaton Rim Brake Ebonite Centrepin Reel

Post by Evert van der Plas »

The reel finished to day, it was a difficult job but manged it to make it work again. i learned new some new skills and i am very pleased with the result as it is.
Here some pictures from before and after the job
The ratchet spring must be replaced, the old one that was in there was broken when i try to clean it, it was a steel spring and rusted until there was not much left off it but will find a good one for the reel

Image
Image
Image
Image
Image
Image
Image
Image

Post Reply

Return to “Traditional Reel Building and Restoring”