Bent brass foot
- Wagtail
- Arctic Char
- Posts: 1622
- Joined: Sat Dec 29, 2012 12:26 pm
- 11
Bent brass foot
Gents I bought a reel at the weekend which seems sturdily built but has a bent brass reel foot. What is my best course of action to straighten it out? Should I heat the brass and try bending back? The foot is held to the backplate by three screws which I'm sure will come undone quite readily.
'The Chub is a very controversial fish. He has a strong army of supporters, but he has an almost equally strong army of detractors. The trouble is that the detractors do not know what they are talking about'. L. Vernon-Bates
- Watermole+
- Chub
- Posts: 1057
- Joined: Thu Mar 15, 2012 11:07 pm
- 12
- Location: Devon & Cornwall border
Re: Bent brass foot
This is a common problem where reels have been dropped.
However, it can usually be straightened out and as you say, by removing it firstly from the reel.
Never try and just cold bend it back with a mallet, or even after heating, otherwise it will deform into a flattened "S" shape. You will need a metal bar of the same radius as the inside of the reel seat and a small piece of metal the same radius as the bottom.
Clamp up firmly against the bar, using the metal support underneath and heat the brass seat with a good blowtorch until it is a dull red then tap it back against the bar with a soft mallet, do not use a hard hammer directly against it.
After reshaping it, heat again and plunge into a either a salt solution or some thin oil emulsion to anneal it, otherwise it will remain brittle and might fracture without warning.
If you get stuck, send a PM.
Regards,
wm+
However, it can usually be straightened out and as you say, by removing it firstly from the reel.
Never try and just cold bend it back with a mallet, or even after heating, otherwise it will deform into a flattened "S" shape. You will need a metal bar of the same radius as the inside of the reel seat and a small piece of metal the same radius as the bottom.
Clamp up firmly against the bar, using the metal support underneath and heat the brass seat with a good blowtorch until it is a dull red then tap it back against the bar with a soft mallet, do not use a hard hammer directly against it.
After reshaping it, heat again and plunge into a either a salt solution or some thin oil emulsion to anneal it, otherwise it will remain brittle and might fracture without warning.
If you get stuck, send a PM.
Regards,
wm+
"Are not two sparrows sold for a farthing? Yet one of them shall not fall without your Father knoweth" ..Jesus of Nazareth, King James AV
- Wagtail
- Arctic Char
- Posts: 1622
- Joined: Sat Dec 29, 2012 12:26 pm
- 11
Re: Bent brass foot
Many thanks wm+ I'll give that a go when I can find a bit of bar of the correct diameter
'The Chub is a very controversial fish. He has a strong army of supporters, but he has an almost equally strong army of detractors. The trouble is that the detractors do not know what they are talking about'. L. Vernon-Bates
- Wagtail
- Arctic Char
- Posts: 1622
- Joined: Sat Dec 29, 2012 12:26 pm
- 11
Re: Bent brass foot
An update to this tale. I chickened out of trying to reshape the foot and sent it to WM+ who very kindly offered to try for me. I think WM+ should be rechristened WM+++++ Many,many thanks to him for undertaking the work for me; it is yet another example of why this forum is so marvelous
So here is the 'before'...
and here is the 'after'....
- he made such a lovely job of the foot that I felt duty bound to polish up the other brass bits
So here is the 'before'...
and here is the 'after'....
- he made such a lovely job of the foot that I felt duty bound to polish up the other brass bits
'The Chub is a very controversial fish. He has a strong army of supporters, but he has an almost equally strong army of detractors. The trouble is that the detractors do not know what they are talking about'. L. Vernon-Bates
- LuckyLuca
- Barbel
- Posts: 4792
- Joined: Mon Jul 02, 2012 10:20 am
- 11
- Location: Oxfordshire
Re: Bent brass foot
Well done Gents!
I walked across an empty land
I knew the pathway like the back of my hand
I felt the earth beneath my feet
Sat by the river and it made me complete.
I knew the pathway like the back of my hand
I felt the earth beneath my feet
Sat by the river and it made me complete.
- Wallys-Cast
- Pike
- Posts: 6635
- Joined: Tue Mar 20, 2012 11:02 am
- 12
- Location: Durham.
Re: Bent brass foot
An excellent job as always by Leszek, it looks perfect.
Alex, not sure if your reel is stamped as sometimes they weren't but it was called the Allbern reel and they are well made.
Once you get the drag and spool release set up they run like an Aerial. It's just a bit awkward needing a screwdriver to adjust the drag but lets face it, drags are seldom used as most people back them right off and use their thumb anyway..
Another one saved to fight another day..
Wal.
Alex, not sure if your reel is stamped as sometimes they weren't but it was called the Allbern reel and they are well made.
Once you get the drag and spool release set up they run like an Aerial. It's just a bit awkward needing a screwdriver to adjust the drag but lets face it, drags are seldom used as most people back them right off and use their thumb anyway..
Another one saved to fight another day..
Wal.
- Aquaerial
- Chub
- Posts: 1182
- Joined: Fri May 09, 2014 6:16 pm
- 10
- Location: Norfolk
Re: Bent brass foot
Such a heartening read...well done guys.
Aquaerial
But Oz never did give nothing to the Tin Man
That he didn't, didn't already have
But Oz never did give nothing to the Tin Man
That he didn't, didn't already have
- Crucian
- Eel
- Posts: 2379
- Joined: Thu Apr 03, 2014 8:20 pm
- 10
- Location: Watchet, Somerset.
Re: Bent brass foot
Well done indeed Watermole
- Wagtail
- Arctic Char
- Posts: 1622
- Joined: Sat Dec 29, 2012 12:26 pm
- 11
Re: Bent brass foot
It is indeed stamped Allbern, and does feel like a well made reel. I haven't got it running all that well... but that might be because I had no idea there was an adjustable drag Do I assume that the adjustment is made via one or both of the large screws on the front?Wallys-Cast wrote: ↑Fri Apr 28, 2017 10:15 am An excellent job as always by Leszek, it looks perfect.
Alex, not sure if your reel is stamped as sometimes they weren't but it was called the Allbern reel and they are well made.
Once you get the drag and spool release set up they run like an Aerial. It's just a bit awkward needing a screwdriver to adjust the drag but lets face it, drags are seldom used as most people back them right off and use their thumb anyway..
Another one saved to fight another day..
Wal.
'The Chub is a very controversial fish. He has a strong army of supporters, but he has an almost equally strong army of detractors. The trouble is that the detractors do not know what they are talking about'. L. Vernon-Bates
- Wallys-Cast
- Pike
- Posts: 6635
- Joined: Tue Mar 20, 2012 11:02 am
- 12
- Location: Durham.
Re: Bent brass foot
You do indeed assume correctly Alex, its a bit hit and miss but once you have a good play with it you will see how it works and how to lock the drag away from the spindle. The one that acts as the spool release is left loose so you can slide it outwards with your thumb nail.Wagtail wrote: ↑Fri Apr 28, 2017 5:26 pmIt is indeed stamped Allbern, and does feel like a well made reel. I haven't got it running all that well... but that might be because I had no idea there was an adjustable drag Do I assume that the adjustment is made via one or both of the large screws on the front?Wallys-Cast wrote: ↑Fri Apr 28, 2017 10:15 am An excellent job as always by Leszek, it looks perfect.
Alex, not sure if your reel is stamped as sometimes they weren't but it was called the Allbern reel and they are well made.
Once you get the drag and spool release set up they run like an Aerial. It's just a bit awkward needing a screwdriver to adjust the drag but lets face it, drags are seldom used as most people back them right off and use their thumb anyway..
Another one saved to fight another day..
Wal.
Wal.